> For the complete documentation index, see [llms.txt](https://docs.paragontruss.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.paragontruss.com/design/how-to/profile-truss/design-with-additional-loads.md).

# Design with Additional Loads

Before you begin, select a profile truss, such as a `Common` truss.

Some trusses carry loads that the load settings don't cover, such as an HVAC unit on the roof. This article adds the unit's weight two ways: as point loads where its legs sit, and as a moving load when you don't know exactly where the unit will go. It isn't meant to be prescriptive for a specific situation; it shows the loading tools available in Paragon Design. For more on creating, editing and deleting manual loads, see [Creating Additional Loads](https://docs.paragontruss.com/design/how-to/general/modify-project-and-component-settings/creating-additional-loads.md).

In this example, the HVAC unit weighs 2000 lb, is 8' by 5', and sits on a stand with legs 3' apart, so each truss under it gets two point loads.

## Duplicate the truss

Keep a copy of the truss for the moving load, so the two examples stay separate.

### Step 1 - Click `Duplicate Truss`

`Duplicate Truss` is in the [Actions Toolbar](https://docs.paragontruss.com/design/getting-started/interface-overview/actions-toolbar.md). The copy is named after the original with `-copy` added, and it's selected, with its `Component Properties` open in the right sidebar.

### Step 2 - Enter a name for the copy, such as `HVAC ML` in `Name`

### Step 3 - In the left sidebar, click the original truss to make it active again

The point loads go on the original truss, and the moving load goes on the copy.

## Add point loads for the HVAC legs

### Step 1 - Click `Create`, choose `Additional Loads`, and choose `Manual Load`

You can also click the menu button next to `Additional Loads` in the right sidebar and choose `Create Manual Load`. The `Manual Load Insertion` panel opens.

### Step 2 - Choose `Select Member` for `Load Insertion Method`, and a member, such as `T1` for `Member`

The first leg sits on the left top chord, T1.

### Step 3 - Choose `Concentrated` for `Load Distribution`

A concentrated load is a point load, one for each leg of the stand.

### Step 4 - Choose `Dead` for `Load Type` and `Down` for `Direction`

### Step 5 - Enter where the first leg sits, such as `1' 6"` in `Point X`

`Point X` is measured along the truss from the left. The load is placed on the member at that point.

### Step 6 - Enter the weight on the leg, such as `500` in `Load Magnitude`

`Add Load` stays unavailable until the magnitude is at least `1`.

### Step 7 - Enter a name, such as `Leg 1` in `Manual Load Name (Optional)`, and click `Add Load`

![](https://2598702589-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzIkcl8vW0QKiqUIx7Xdc%2Fuploads%2FzOkLMBaui170qhk7gb44%2Fawl-manual-load-insertion.png?alt=media)

### Step 8 - Enter where the second leg sits, such as `4' 6"` in `Point X`

The legs are 3' apart. The other settings stay as they were for the first leg.

### Step 9 - Enter a name, such as `Leg 2` in `Manual Load Name (Optional)`, and click `Add Load`

Both loads are listed under `Add Load`. To remove one before you insert, click `Delete Manual Load` next to it.

### Step 10 - Click `Insert`

Given the size of the unit, you could divide its weight over several trusses. This example takes the conservative route and puts both legs' full load on one truss.

## Check that the loads show in the scene

### Step 1 - Click `View Options`

`View Options` is the eye icon in the toolbar.

### Step 2 - Make sure `Show Manual Loads When No Other Loads Visible` is checked

It's checked by default. When it's checked, manual loads show on the truss whenever no other loads are shown.

![](https://2598702589-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzIkcl8vW0QKiqUIx7Xdc%2Fuploads%2FL1a2Q3yupvHDUMRhxj4W%2Fawl-view-options.png?alt=media)

### Step 3 - Click `Close`

## Analyze the truss with the point loads

### Step 1 - Click `Analyze`

### Step 2 - Click `Analysis and History` to see the results

In the video, this truss works with the point loads. To view the results, see [Run & View Component Analysis](https://docs.paragontruss.com/design/how-to/general/run-and-view-component-analysis.md).

## Add a moving load to the copy

When you don't know exactly where the unit will be placed, a moving load checks it at points along the whole top chord.

### Step 1 - In the left sidebar, click the copy, such as HVAC ML, to make it active

### Step 2 - Click `Create`, choose `Additional Loads`, and choose `Moving Load`

You can also click the menu button next to `Additional Loads` in the right sidebar and choose `Create Moving Load`. The `Define Moving Load` panel opens.

### Step 3 - Choose `Distributed` for `Load Distribution`

The magnitude changes to pounds per square foot.

### Step 4 - Enter the load, such as `175` in `Load Magnitude`

### Step 5 - Make sure `Use Panel and Mid-Panel Points?` is checked

It's checked by default. The load is then applied at the panel points and mid-panel points along the member, instead of at locations you enter.

### Step 6 - Enter the length of the load, such as `3'` in `Distributed Load Length`

### Step 7 - Choose `Dead` for `Load Type` and `Top Chord` for `Along Member Type`

### Step 8 - Enter a name, such as `HVAC ML` in `Moving Load Name (Optional)`

![](https://2598702589-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzIkcl8vW0QKiqUIx7Xdc%2Fuploads%2FWGBLULdo5VGdSPaYwtiB%2Fawl-moving-load-settings.png?alt=media)

### Step 9 - Click `Insert`

## Analyze the truss with the moving load

### Step 1 - Click `Analyze`

### Step 2 - Click `Analysis and History` to see the results

To see the moving load in the load cases, expand Load Cases in the right sidebar: the moving load is applied along the top chords. In the video, the truss is adequate once the top chords are upgraded to 2x6 No. 1 Southern Pine. Hover over a top chord in the scene to see its information. To change a member's lumber, see [Add and Modify Members](https://docs.paragontruss.com/design/how-to/general/members.md#lumber).

## Watch the video

The video shows the same steps on a dual-pitch truss, with the point loads on the flat area at its left end. In the video, the copy is named Dual Pitch with HVACML, and the loads are created from the menu next to `Additional Loads`.

{% embed url="<https://youtu.be/r-QtzE_CUc8>" %}

<details>

<summary>Video Transcript:</summary>

Welcome! In this video, we’ll walk through adding manual load cases to our truss. For this project, we are going to simulate the added load of an HVAC unit on a roof. This video is not intended to be prescriptive for a specific situation, but rather it demonstrates how to use some of the loading tools available within Paragon Design. First, let’s duplicate the truss so we can keep our existing work separate. In the actions toolbar let’s click on the duplicate truss icon. Let’s rename the truss in the Component Properties panel to be Dual Pitch with HVACML.

Before we begin let’s make the original truss active in the components panel along the left sidebar. Click on the Dual Pitch with HVAC to make it the active truss.

As you see, we’ve designed this dual-pitch truss and we need to add a manual load to the flat area on the left side.

• We know that our HVAC unit weighs 2000 pounds

• The size is 8 feet by 5 feet

• Will be on a stand with legs spaced 3 feet apart, so we need to add two point loads to account for this.

Navigate to the Additional Loads in the Collection Subpanel and click the menu button. Click Create Manual Load to open the Manual Load Insertion subpanel. Click the Load Insertion Method and use the Select Member option. Make sure the load distribution is set to Concentrated. Use the member select to specify T1 as the target member. This will be a dead load with the direction set to down. We know the first leg is 1 and a half feet from the left along the x axis. We will set the load magnitude to 500 pounds and give the manual load a name Leg 1 for easy identification and click ADD LOAD. The next leg is at 4 and a half feet. Update the Point X and name it Leg 2. Then click ADD LOAD. Now that we’ve added both point loads, click insert. Given the dimensions of this HVAC, we could divide the weight over multiple trusses, but for this example we are going the conservative route.

Great, we’ve added two manual point loads for the HVAC unit. By default, “Show Manual Loads When No Other Loads Visible” should be checked. If you do not see your manual loads, open the View Options Menu to verify this is checked.

Now let’s analyze this truss. Great! This truss will work in this scenario.

Let’s consider another example. Here we don’t know exactly where the HVAC unit will be placed, so we need to place a moving load along the entire top chord.

Next, select the truss we duplicated earlier with the name Dual Pitch with HVACML.

Now navigate to the Additional Loads menu, then to Create Moving Loads.

Here we will select Distributed for Load Distribution.

Set the Load Magnitude to 175 psf.

Make sure “Use Panel and Mid-Panel” points is checked.

Set the Distributed Load Length to 3 feet.

Make sure the Load Type is set to Dead.

And for Along Member Type make sure Top Chord is selected.

We will name this moving load HVAC ML.

Next click insert.

Now analyze this truss.

If we navigate to the load cases and then expand the list. We can see the truss has the moving load applied along the top chords.

It looks like this truss will be adequate as long as the top chords are upgraded to 2x6 Number 1 Southern Pine. By hovering over the top chords the member’s information will display.

We hope this provided a better understanding of some of the tools available for designing trusses with unique loads.

</details>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://docs.paragontruss.com/design/how-to/profile-truss/design-with-additional-loads.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
